Golf Putters-Everything You Need to Know About It

golf putters

The golf putters are one of the most popular golf clubs that are used on almost every hole. Unless a golfer hits a marvelous shot that falls right into the cap, he will have to use the putter to finish the shot properly. Putters were originally made out of one solid piece of metal until the Ping Company brought a revolution in the industry in 1959 with its perimeter weighted club head.

Ping Company later introduced a product, named ‘Anser’, which was the first-ever putter having a bent shaft. In modern days, the golfer can choose from a variety of materials, design.

Functions:                                               

Basically, the putter is used to push the ball to the hole once the player has reached the green. Its loft is so little so the ball will roll along the low grass of the green. The golf putters have not any grooves on the clubface to give the golf ball additional spin.

Shaft Length:

The shaft length of the standard putter is 33 and 36 inches long. To use this putter, a golfer must lean over and hang down his arms. Belly putters have a 41-46 inch long shaft. It rests against the player’s stomach to stops his hands from moving around the putt. If a golfer wants more stability, he can choose the long putter that is about 52 inches long. The golfer has to bend over to place his chin on the end of the long putter to anchor it.

There are some putters which are “heel-shafted”, with the shaft attaching at or very near the club head’s heel.

If the shaft attaches within the middle of the club head, the club is called “center-shafted” putter.

It the club head is set back, relative to the longest a part of the shaft, it is termed as an “offset” putter. A putter with bent shafts is named “single-bend” or “double-bend” putters, depending on the amount of bends within the shaft.

Putter Shafts and Hosels:       

Almost all putters have steel shafts that allow a consistent and strong feel. Hosel means the point where a shaft meets the putter head. There are some few options:

Centre Shafted Putters:

The centre shafted putters connect in the same way but lengthwise they meet the putter in the centre of the head. It is totally a personal preference to choose a centre shafted putter. All golfers pay close attention to the putter’s hosel. Some like to have the hosel at the middle to direction the ball to the hole. And the other prefers heel-shafted putters.

Heel Shafted Putters:

A heel shafted putter’s shaft connects directly with the putter head on the end close to the player.

Hosel Offset:

An offset at the hosel is a kind of variation in some putters. This is the point at which the hosel is bends in reverse to push the lower part of the shaft forward of the essence of the putter to draw a player’s hand in front of the ball through effect. Actually all putters have some degree of offset in them.

Club Head and Club Face:

The main putter design is blade that is small and flat club head. Basically mallet-style putters have much larger and heavier club and little and no backspin. The weight of the club head is perfectly balanced across the face. Peripheral weighted putters have a larger club head. But the weight is slightly off-balance. These putters are the best for golf players who hit the ball with a slightly inside-out swing.

A putter’s club face’s angle is generally less than five degrees that minimizes the loft on the ball. The metal faced putters can be made from different types of materials such as copper, aluminum, bronze and titanium.

Some putters have a metallic face with a plastic insert in the center. The insert softens the power of the golf club striking the ball and expanses the weight of the edges of the club head for a larger sweet spot.

Shaft Design:

The putter is the only golf club that has permission to have a bent shaft under USGA official rules. This bend aligns the sweet spot of the club head with the grip and makes it easier to line up the putt. The putter shaft’s grip end design may also differ from the round shape of a golf iron or a putter. General putter grips have one flat side to prevent the club head from rotating on contact.

Golf Putter’s Length:

Basically, the rules of Golf clubs limit to forty-eight inches in length- except for putters. While a standard putter is almost 35 or 36 inches long, skilled players use additional long putters, even some which push past the forty-eight inches limits that apply to other clubs.

‘Belly Putters’ are called the most common longer golf putters. Because the golfer rests the end of the grip on his/her belly after beginning stroke. Other extra-long putters termed ‘broomsticks’ or just ‘long putters’. Some have two grips on which the player separates his hand, placing one on each grip.

Putter Head Design:

Blade Golf Putters:

blade golf putters
blade golf putter

The blade is the most traditional type of putter. Using a relatively small head, its classic design is so popular in golf from 1900-1990 and players are still using it. The simple and flat look was easy to produce in the past days of golf club production. And the soft hit a blade produced was likable on many different types of greens. Blade putter will suit a player with a straight putting stroke.

Peripheral Weighted Golf Putters:

Peripheral Weighted Golf Putters
Peripheral Weighted Golf Putters

The peripheral/heel-toe weighted putter was the natural evolution of the blade putter. Long and thin address, the design could still be soft but with added weight in the heel and toe portions adding more consistency and forgiveness. It is made by the famous Ping Anser. It was designed in 1966.

This shape of putter revolutionized the game. And golf players are still using it.

Mallet Golf Putters:

Large head in driver design made tee shots more compatible, the mallet shaped putter gave the same benefit to the player on the green. Sometimes putter makers employ various alignments aids and shapes on the rear of the head to give assistance the players align to puts better.

mallet putter
mallet putter

The deep designs of the putter’s head offer producers to have a much lower and deeper center of gravity as well as rising the MOI (Moment of Inertia), which minimizes spins and improves performance on off-center putts. Therefore mallet putters have better face balanced and suited to straight strokes.

About putter’s face

Metal Faced Golf Putters:

Basically traditional putter face material is steel. Other types of metal such as bronze, aluminum, brass, zinc, titanium have been used in the past and many of them are being used today. The extremely strong, heavy nature of metal suits putter faces very well. Among them, steel has a reputation for a hard and also responsive strike giving the putters a solid and controlled feel.

A metal-faced putter has a benefit that it produces a louder noise. Immediately you can hear the sound when the putter pushes the ball.

Some metal faced putter also feature milling on the face that makes a player feel and sound softer though there is less material in contact with the ball. But may sound odd to have rough face.

Insert Faced Golf Putters:

Insert putters are basically metal putters. But their metal face is being replaced with a light-weight nonmaterial insert. The main advantage of using a lightweight insert is that the weight of the putter easily redistributed and added the heel and toe of the putter increases the MOI and offers more forgiveness.

The majority of insert faces are specially designed to give a softer feel than traditional steel. On the other hand, some modern insert faces are designed to replicate the metallic sound and a feel of steel in a lighter-weight insert.

The positive side of insert faced putters is that they enable a player to play with a former cover ball and still have the same level of feeling as if a player using a softer one with a metal face.

If you want to collect more knowledge, search on the internet for further information and you can also take help from professional golf players. And also if you want to know about golf wedge, click here.

Leave a Reply

Your email address will not be published. Required fields are marked *